 |
||||||||
Card Making Project - Wedding Rings Gatefold Card
Made by Linda
Linda created this card in Ice Silver and Stardream Silver using the Marianne Creatables Petra's Oval die and Wedding Rings die.
You will need a die cutting machine for this project.
|
||||||||
 |
To make this card you will need:
 A4 Stardream Silver CardPieces of Stardream Silver Card for die cuttingA4 Ice Silver CardSmall Piece of Silver Mirror CardMarianne Creatables Petra OvalMarianne Creatables Wedding RingsBudding Vine Embossing FolderSwiss Dots Embossing FolderDie Cutting Machine - Cuttlebug, Big Shot or Grand CaliburSilver on White Congratulations RibbonWedding Sentiments Peel Offs - SilverGlitter Rope Borders - Silver/ClearPhoto Glue3D Double Sided Foam Pads 10mm Square 3D Double Sided Foam Pads 3mm Thick 5mm Double Sided Fingerlift Tape Scoring Board such as the EaziScore or Hougie Board |
|||||||
Crease the A4 Stardream Silver card to create an A5 gatefold card. If you don't have an EaziScore, where the A4 gatefold lines are marked, then turn your card so that it is A4 landscape and score the card at 74mm from each side.
Cut 2 pieces of the Ice silver card to each measure 140mm x 205mm. Using the Budding Vine embossing folder at the bottom of the card and the Swiss Dots embossing folder at the top run the card through the die cutting machine.
Please note: there will be a gap in the centre between the 2 embossing folders that will later be covered by the ribbon.
Once the card is embossed cut it lengthways down the centre to create 2 pieces each measuring 70mm x 205mm.
Take 2 small lengths of ribbon and wrap one around each piece of card to cover the middle (unembossed) section securing the ribbon at the back of the card with double sided tape. Using photo glue stick one of the embossed Ice Silver cards to the right hand side and one to the left. Go around the edges of both using silver/clear glitter rope border peel offs.
Using the largest and second smallest of the Marianne Creatables Petra Oval die set and the Stardream Silver card run it through the die cutting machine once to cut, then change plates and run it through again to emboss.
Using Ice Silver card and the second largest die from the Petra Oval set run it through the die cutting machine once to cut and then again to emboss.
Using a small piece of silver mirror card and the Marianne Creatables Wedding Rings run it through the die cutting machine once to cut and then again to emboss.
Mat and layer the die cuts as follows:
Ice Silver card from second largest die layered on Stardream Silver card from largest die using 10mm square 3D foam pads.
Stardream Silver card from second smallest die layered onto Ice Silver card using 10mm square 3D foam pads.
Silver mirror card wedding rings onto smallest Stardream Silver card using 3D foam pads 3mm thick.
Using photo glue or double sided tape on only half of the back of the layered die cuts attach to the creased card on the left hand side (as the card faces you) of the gatefold.
If you have used photo glue you may need to hold in position whilst the glue dries.
Cut 2 pieces of Stardream Silver card - one measuring 40mm x 18mm and the other measuring 67mm x 18mm and 2 pieces of Ice Silver card - one measuring 37mm x 15mm and the other 64mm x 15mm. Glue the smaller piece of Ice Silver centrally to the smaller piece of Stardream Silver using photo glue and add the On Your silver peel offs. Glue at an angle at the top of the left gatefold using 10mm square 3D foam pads . Glue the remaining pieces of Ice Silver and Stardream Silver card and add the Wedding Day peel offs. Glue at an angle at the bottom of the right gatefold 10mm square 3D foam pads.
Take 2 of the double hearts from the peel off sheet and place one in the bottom corner of the left gatefold and one in the top corner of the right gatefold.
********************************
Please feel free to copy this card for your own use. Our angel policy can be accessed via the Gallery home page.
______________________________________________________________________________
|
||||||||
 |
||||||||
